Swiss3D

CNC milling and turning
to your drawing.

3-, 4- and 5-axis milling and CNC turning in aluminium, steel, stainless steel, brass and plastics. From prototype to series, every part reviewed by a manufacturing expert.

  • 3-, 4- & 5-axis milling
  • CNC turning
  • Prototype to series
CNC milling and turning to your drawing
  • Siemens
  • Bosch
  • NVIDIA
  • Logitech
  • Novartis
  • ETH Zürich

Milling and turning.

We mill on 3, 4 and 5 axes and turn rotationally symmetric parts, from simple milled parts to freeform geometry.

Send inquiry
  • 3-axis milling

    The standard process for prismatic parts such as plates, housings, brackets and fixtures. The cutter moves in X, Y and Z. Machining is done from above; for further sides the part is re-clamped. The most economical solution for most milled parts.
  • 4-axis milling

    An additional rotary axis turns the workpiece during machining. Side holes, slots and wrap-around contours are produced without re-clamping. This saves time and improves accuracy between the sides.
  • 5-axis milling

    Two rotary axes tilt the workpiece. Freeform surfaces, angled holes and several sides are machined in one setup, for example for impellers, mould inserts or complex structural parts.
  • CNC turning

    The workpiece rotates in the chuck while the turning tool follows the contour. Suited to rotationally symmetric parts such as shafts, pins, bushings and flanges. Diameters, grooves, chamfers and radii are produced in one setup with high concentricity.

Materials & finishes.

First the material, then the matching post-processing. You choose both directly in the configurator.

Material

Steel

Structural and heat-treatable steel for loaded machine parts.

  • Structural steel S235

    Unalloyed structural steel, easy to weld. For brackets, plates and structural parts.

  • Heat-treatable steel 42CrMo4

    Chromium-molybdenum steel with high strength and toughness, for shafts, axles and gears.

Post-processing for Steel

  • Electroless nickel10–25 µm

    Uniform, hard nickel layer, even in bores and internal contours.

  • Hard chrome plated

    Very hard, wear-resistant chrome layer, ground after plating.

  • Zinc plated, blue passivated5–12 µm

    Proven corrosion protection for steel parts with a bluish silver sheen.

  • Black oxideapprox. 1 µm

    Black, almost dimensionally neutral surface. Corrosion protection only in combination with oil.

  • Phosphated5–15 µm

    Matt grey layer and a good primer for paint; with oil also corrosion protection.

  • Powder coated (RAL)60–100 µm

    Tough, impact-resistant paint layer in the RAL colour of your choice.

  • Wet painted (RAL)30–60 µm

    Smoother paint finish than powder, but somewhat more delicate.

  • Laser marked

    Permanent marking with text or a number at the position given on your drawing.

Sample images created with AI.

A quote for your CNC parts.

Send your STEP file and drawing. A manufacturing expert reviews your part and prepares a binding quote.

Send files

Compared with conventional sourcing.

No supplier search, no customs paperwork, one contact person. Here is how a request to Swiss3D differs from classic sourcing.

Quote

Swiss3D

Binding, usually within a few hours

Classic sourcing

Ask several suppliers and compare quotes

Contact

Swiss3D

Your dedicated contact person

Classic sourcing

Changing contacts, often several suppliers

Manufacturability check

Swiss3D

Every part reviewed by a manufacturing expert before you get the quote

Classic sourcing

Issues often surface only through supplier queries

Finishing

Swiss3D

Material and finish from a single source

Classic sourcing

Finishes often at separate companies

Delivery & customs

Swiss3D

Shipped from Switzerland

Classic sourcing

Customs to be organised yourself when ordering abroad

Minimum quantity

Swiss3D

From 1 piece, prototype to series

Classic sourcing

Often a minimum order value

Tolerances and specifications from your drawing.

Send your drawing as a PDF along with the STEP file. We machine exactly to your specifications.

Send STEP file and drawing
Animation: technical drawing of a bearing flange with fits, surface roughness and geometric tolerances 1122334455667788AABBCCDDEEFFWerkstoffEN AW-6082 T6OberflächeEloxiert naturMassstab2:1Gewicht0,127 kgFormatA3ProjektionAllgemeintoleranzenISO 2768-mKOberflächenangabenISO 1302GezeichnetE. Dubach 15.09.2026GeprüftBenennungLagerflanschFirmaSwiss3D GmbHZeichnungsnummerS3D-2026-0147RevisionABlatt1 / 1Weitergabe sowie Vervielfältigung dieses Dokuments nur mit ausdrücklicher Genehmigung. Schutzvermerk nach ISO 16016.AAA-AØ35 H7Ø52 f7Ø80Ø281110164x Ø6,6 durchØ114,4Ø66Ra 0,8Ra 1,6Ø0,02A0,02AANicht bemasste Kanten gebrochen 0,2 × 45°Eloxiert E6/EV1 natur, Schichtdicke 15 µmPassmassAbmasseØ35 H7+0,025 / 0Ø52 f7−0,030 / −0,060Ra 3,2
Example: bearing flange

Every callout counts

  • Ø35 H7Fit for the bearing seat. The bore must be between 35.000 and 35.025 mm.
  • Ra 0,8Roughness of the bearing surface, much finer than as machined (Ra 3.2).
General tolerance
ISO 2768-mK or -fH
Fits
IT6 to IT9, e.g. H7, h6, g6
Surface roughness
Ra 3.2 to Ra 0.4
Threads
M1.6 to M20, G1/8 to G1/2

Frequently asked questions.

  • We offer 3-, 4- and 5-axis milling as well as CNC turning. Parts that need both turning and milling are produced as combined turn-mill parts.
  • Ideally a 3D model in STEP or STP format. An STL file is not suitable because it contains no real surfaces and radii. If you have tolerances, fits or threads, also send the technical drawing as a PDF. If you only have a drawing, we can quote from that too.
  • Aluminium (6061, 7075), steel (S235, 42CrMo4), stainless steel (1.4301, 1.4404), brass (CuZn39Pb3) and the plastics POM-C, PA6, PMMA and PC. Other materials such as titanium or PEEK are available on request.
  • The standard is ISO 2768-mK. Finer general tolerances to ISO 2768-fH, fits from IT6 to IT9 such as H7 and surface roughness down to Ra 0.4 are produced per drawing.
  • When a part has freeform surfaces, angled holes or features on several sides. What would otherwise need several setups is done in one, which improves accuracy between the surfaces.
  • The price mainly depends on material and stock, the number of setups, machining time, tight internal radii, tolerances, finishes and quantity. Send us your STEP file and drawing and you will usually receive a binding quote within a few hours. Request a quote.
  • No. We make prototypes from a single piece as well as series. Because every part has to be set up, the unit price drops significantly with quantity.
  • We tell you with the quote and explain why, for example an undercut no cutter can reach. Metal 3D printing is often the better solution because it builds such geometries without tooling. More about metal 3D printing.

Request CNC parts.

Send us your 3D model and drawing. A manufacturing expert reviews your part and prepares a binding quote.

  • Quote usually within a few hours
  • Reviewed by a manufacturing expert
  • Confidential, NDA on request

Prefer email? info@swiss3d.ch

3D model and drawing
Drag files here or browseSTEP, IGES, PDF, DXF or ZIP, up to 50 MB per file

We treat your data and files confidentially and use them only for this quote.